ROAD PROFILERS AND STABILISERS

35 years
With over 30 years experience, you can rely on Hydrapower!

Queensland's Premier Road Profiler Source 

Profilers and stabilisers are arguably the one piece of ground working equipment that takes the most punishment. These machines are designed to virtually tear up the road and that is exactly what our high-quality attachments do. Our durable range is suitable for a range of skid steer applications and is manufactured to the very highest specifications.

AC Profiler/Stabiliser

  • State-of-the-art road stabiliser
  • Engine Type: John Deere /Cummins 
  • Engine Size: 203 hp 
  • Working Depth 300 mm
  • Runs at 14 metres/minute, at full depth, depending on road condition

Features and Benefits
  • Safety - Drum housing is fully enclosed so that milled debris is contained at all depths
  • Wide range - Available in widths from 450mm to 1000mm with depths up to 250mm
  • Easy Maintenance - Easy access to picks for cleaning
  • Options - Stabiliser drum and water tank

92TS Tractor Stabiliser

  • Suits minimum 84 KW (115 HP) tractor with creeper gear 
  • Stabilises 1800 mm wide x 300 mm deep (other widths available) 
  • Ideal for working on country roads 
  • Capable of travelling between jobs at 40 km/h 
  • Built in, closed loop hydraulic circuit, including oil cooler and comprehensive filtration, with pumps driven off tractor PTO 
  • Hydraulically operated height adjustment 
  • 120 litre Hydraulic oil tank 
  • Hydraulically operated rear covers to ensure cutting area covered at all cutting depths
* AC Profiler/Stabiliser TS Tractor Stabiliser (92TS)
* “Utility “Utility
Host Machine Size High-Flow Skid Steer (Wheeled or Tracked) 115 hp - 140 hp Tractor (Requires ground speed of 140m/hr or less).
Primary Task Repairing Road Failures &/or Road Stabilizing Repairing Road Failures and Road Stabilizing
Cutting Sizes Available
(Width mm x Depth mm)
and Hydraulic Power Requires
450 mm x 150 mm, 30 kw - 40 kw (for hotmix milling)
450 mm x 200 mm, 34 kw - 75 kw (for hotmix milling
600 mm x 200 mm, 48 kw - 75 kw (for hot mix milling)
750 mm x 250 mm, 55 kw - 75 kw (for hotmix milling)
1000 mm x 250 mm, 63 kw - 75 kw (for hotmix milling)
1800 mm x 300 mm (as per tractor's power)
2000 mm x 300 mm (as per tractor's power)
Side Shift Hydraulic, Centre to Left N/A
Tilt and Tilt Angle Hydraulic, 450 mm cut Profilers 15o Left or Right,
600 mm+ cut Profilers - 10o Left or Right
N/A
Depth Control Hydraulic - infinitely variable Hydraulic - infinitely variable
Drive Mechanism Hydraulic motor via a planetary reduction gearbox
fitted with a duo-cone seal
2x Hydraulic motors via a planetary reduction gearboxes
fitted with a duo-cone seal
Number of Cutting Picks 450 x 150 cut = 48 Picks
450 x 200 cut = 56 Picks
600 x 200 cut = 70 Picks
750 x 250 cut = 96 Picks
1000 x 250 cut = 120 Picks
1800 x 300 cut = 160 Picks
2000 x 300 cut = 176 Picks
Hydraulic Flow Required 450 x 150 cut is 90 lpm - 130 lpm
450 x 200 cut and above is 100 lpm - 170 lpm
Determined by Tractor's Power
Hydraulic Pressure Required 450 x 150 cut is 170 - 220 bar
450 x 200 cut and above is 206 - 345 bar
Determined by Tractor's Power
Comments For single system loaders extra valving is required
on attachment which will incur an additional charge.
Tractor must have a minimum of three separate remotes
Water Tank Option Available? YES YES
* * *
hydrapower-attachments-profile-stabiliser-diagram

Call the team today on 07 3490 5100 to discuss your requirements.

Share by: